3 zone Lemon cymbal with only 1 input

LooseSends
Posts: 96
Joined: Sun Jan 23, 2022 5:46 pm

Re: 3 zone Lemon cymbal with only 1 input

Post by LooseSends »

I apologize in advance for double-posting (I just put up a new thread today) but I need to know if my Lemon 18" is defective or it happens to be me that's defective since I can't get the bell to trigger at all.

It's set up as a Roland 3-zone Ride. Depending on the order I plug the two stereo input jacks in I either get nothing at all (bow sometimes triggers when hit very hard,) or only bow & tip triggering. I have also tried switching the quick-connect internally but that didn't seem to help.

Just to be clear, I get no apparent signal for bell hits at all no matter how hard I hit.

Also, I do get choke which works fine.
User avatar
Rob
Site Admin
Posts: 4654
Joined: Sat Aug 01, 2009 2:04 pm

Re: 3 zone Lemon cymbal with only 1 input

Post by Rob »

This seems to contradict what you've said in the link below. Please clarify. And make sure you unplug the pads from the eDRUMin when switching cables around.

viewtopic.php?f=29&t=1439
mprinz
Posts: 399
Joined: Tue Jan 07, 2020 12:39 pm

Re: 3 zone Lemon cymbal with only 1 input

Post by mprinz »

Hi, in the case of no signal.
Check your cables.
I would take a multimeter/voltmeter/circuit analyzer and check if the
bell switch is working. If it works the signal is lost on it's way to the jack.
As I know the build quality of those cymbals it could also be a cold joint on the PCB.

What about your input wiring mode?
LooseSends
Posts: 96
Joined: Sun Jan 23, 2022 5:46 pm

Re: 3 zone Lemon cymbal with only 1 input

Post by LooseSends »

mprinz wrote:
Thu Feb 17, 2022 10:50 pm
Hi, in the case of no signal.
Check your cables.
I would take a multimeter/voltmeter/circuit analyzer and check if the
bell switch is working. If it works the signal is lost on it's way to the jack.
As I know the build quality of those cymbals it could also be a cold joint on the PCB.

What about your input wiring mode?
I'm not sure what contradiction I made in my other post, if you could clarify for me, Rob?

I have a multimeter and some basic experience using it but tbh I'm not sure what I should be checking for since I don't really know how the switches work on a two input ride, or how to know what I'm looking for really to test if the bell is working.

If I know I have the right jack hooked up with the quick-connect it would be a good start. Having it on either jack didn't give me a bell signal either way but at least I could narrow down how I should be testing it.

Meanwhile I'll look for some bad solder I guess.
Retro Rambler
Posts: 24
Joined: Sat Jul 18, 2020 2:33 pm

Re: 3 zone Lemon cymbal with only 1 input

Post by Retro Rambler »

Glad it is working for you! I may take the lazy way out (at least for now) for the new cymbal adds and just run 2 cables each for the extra ride and crash I'm adding, I have enough parts to make a couple more adapter cables but right now I don't need them.
Custom 12pc E-kit | UFO Drums Bass Trigger | ATV Cymbals | 1x ED10+4x ED4 | RME HDSPe RayDAT | SD3+SDX's | 2 working brain cells
User avatar
Rob
Site Admin
Posts: 4654
Joined: Sat Aug 01, 2009 2:04 pm

Re: 3 zone Lemon cymbal with only 1 input

Post by Rob »

Mprinz,

Does your adapter work reliably in version 2 now. I made some small changes to try to fix your issue. Would be great to know if the changes resolved your issues or if I need to make more adjustments.
mprinz
Posts: 399
Joined: Tue Jan 07, 2020 12:39 pm

Re: 3 zone Lemon cymbal with only 1 input

Post by mprinz »

Hi Rob,

With regard to the edge sensitivity?
It's great. I am fine. No unwanted edge triggers.

Thank you!

Manuel
Post Reply